ANTEC P180 MANUAL PDF

Page 3 At Antec, we continually refine and improve our products to ensure the highest quality. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Page 4 Loosen the two thumbscrews holding the plastic structure. Slide the large piece all the way to the rear of the case to fully extend the opening and carefully guide all the power cables through the openings to the upper chamber. Note: You may want to pull the power cable of the mm fan from inside the lower chamber to the upper chamber for easy cable management. Page 5 Note: Please check your motherboard manual for your USB header pin layout and make sure it matches the table below.

Author:Magar Mazukazahn
Country:Morocco
Language:English (Spanish)
Genre:Software
Published (Last):23 May 2018
Pages:166
PDF File Size:7.81 Mb
ePub File Size:18.80 Mb
ISBN:917-9-17239-383-8
Downloads:78845
Price:Free* [*Free Regsitration Required]
Uploader:Meztilkis



As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Make sure you choose a power supply that conforms to the newest ATX standard and is compatible with your motherboard. Make sure you turn the switch to the ON I position before you boot up your computer for the first time.

This lets you turn your computer on and off by using the soft switch on your computer case. Setting Up 1. Place the case upright on a flat, stable surface with the rear of the case facing you. Remove the thumbscrews from the right side panel. Grip the panel at the top and bottom and slide it towards you to open the case. Remove the screws from the left side panel. Grip the panel at the top and bottom and slide it towards you to remove the left side panel.

Note: Do not use your fingernails to pry or lift the panels. Inside the case you should see two separate chambers - the upper chamber for motherboard, external drives and hard drives; and the lower chamber for power supply and hard drives.

Installing the power supply 1. With the case upright, remove the power supply-retaining cage by removing the screws fastening the cage at both sides. With the power supply inside the cage, slide the cage with power supply into the case.

Between the two chambers there is a plastic structure that lets you run the cables to the upper and lower chambers. It is a two-piece structure — one large and one small. Both pieces can slide back and forth to adjust the openings. Loosen the two thumbscrews holding the plastic structure. Slide the large piece all the way to the rear of the case to fully extend the opening and carefully guide all the power cables through the openings to the upper chamber.

Note: You may want to pull the power cable of the mm fan from inside the lower chamber to the upper chamber for easy cable management. Secure the power supply by fastening the retaining cage to the case with screws.

In addition to the retaining cage, fasten the power supply to the back of the case with the screws provided. Note: You can mount the power supply either side up. Tighten the screws on the back of the power supply, followed by the screws for the power supply retaining cage.

Slide the small plastic piece to the rear of the case to fully extend the other opening. Carefully run the power cables to the lower chamber for the hard drives you are planning to install there.

Slide both the large and small plastic pieces all the way to the front of the case to close the openings when finished with the hard drive installation. Tighten the two thumbscrews on the plastic structure. Cable Organizer You can route data and power supply cables through the holes behind the motherboard tray. Remove both side panels. Pass the cables through the holes behind the motherboard tray and use the cable ties to hold them in place.

Please consult your motherboard manual for specific mounting instructions and troubleshooting. Lay the case down, with the open side facing up.

The drive cages and power supply should be visible. Line up your motherboard with the standoff holes and remember which holes are lined up. Remove your motherboard by lifting it up.

Install standoffs as needed and put the motherboard back in. Screw in your motherboard to the standoffs with the provided Philips-head screws. Your motherboard is now installed. Connecting the Power and LED 1. You may use these LEDs for two hard drives. Connect the pin connector to your motherboard headers so that the blocked pin fits over the missing header pin.

Note: Please check your motherboard manual for your USB header pin layout and make sure it matches the table below. This adapter will allow you to connect the front USB to your motherboard on a pin-by-pin basis.

HAZEN WILLIAMS NOMOGRAPH PDF

Antec P180 User Manual

Page 2 At Antec, we continually refine and improve our products to ensure the highest quality. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Page 3 If it does not match this Intel standard, please contact your motherboard manufacturer for an adapter. This adapter will allow you to connect the front USB to your motherboard on a pin-by-pin basis. This adapter will allow you to connect the front IEEE port to the external-type connector. Page 5 3.

2009 TOYOTA TACOMA OWNERS MANUAL PDF

Antec P180, P182SE, P182 User Manual

.

C PROGRAMMING IN EASY STEPS MIKE MCGRATH PDF

.

Related Articles