APS997C INSTALLATION MANUAL PDF

Page 3 3 of Choose a location above the belt line dashboard of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle.

Author:Meshicage Brarr
Country:Bhutan
Language:English (Spanish)
Genre:Relationship
Published (Last):6 April 2015
Pages:256
PDF File Size:2.53 Mb
ePub File Size:15.8 Mb
ISBN:256-8-93222-700-4
Downloads:14683
Price:Free* [*Free Regsitration Required]
Uploader:Mora



Page 3 3 of Choose a location above the belt line dashboard of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception.

Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method.

This wire will show 0 volts when the key is turned to the "OFF" In most cases, the Purple wire will need to be connected to only one door switch no matter how many doors the vehicle has as most door lighting circuits are wired in parallel. Page 12 A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger.

In this case, connect the Light Blue Wire to terminal 86 of a external relay. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. Pressing the pre-programmed transmitter button s will access channel four and will remain active, for up to 20 seconds, as long as the transmitter button s is held.

Page 17 NOTE: This is a normally opened starter cut arrangement, when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Page 19 3 Wire Ground Switched Door Lock Circuits: In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay.

See owners manual for turning this feature on from the transmitter. Once activated, the unit will start 1 time if the vehicle temperature reaches "0 " and then will run the allotted time.

Page 23 coils. To achieve optimum performance the coil signals must be evenly distributed. This is accomplished by first mapping out the firing order of the engine in groups of as indicated below. Draw a circle around any of the columns. Page 25 NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down.

This must be explained to the operator as it is in contrast to the normal opera- tion of a vehicle utilizing an electrical neutral start switch and is inconsistent with the operators manual. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.

Cut this wire and connect the ignition cylinder side to chassis ground. If the vehicle has delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the interior light delay.

AD&D 2ND EDITION PLANESCAPE PDF

Prestige APS-997C Installation Manual

The dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren sounds one chirp. Simply close the opened entry point to provide full protection. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Again, closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction.

ASTM A424 PDF

Operating the Audiovox APS997C Remote Start System

.

Related Articles